Seagate ST318406LW Guía de instalación descargar pdf (Pagina 2)

Figure 2. Option select jumpers.

6. Mount the drive in the host system and connect cables

Note. LC drives are designed to be attached to a carrier or tray and

inserted into the host system without I/O or power cables.

a. Mount LW model drives to the host system’s chassis using four 6-

32 UNC screws. Two mounting holes are in each side of the drive

and there are four mounting holes in the bottom of the drive. Do not

over-tighten or force the screws. You can mount the drive in any

orientation.

b. Connect the SCSI I/O cable into the drive’s SCSI connector. Take

care not to stretch or crimp this cable, and do not block the sys-

tem’s cooling air flow with the cable.

Note. For Ultra2 and faster operation, special twisted pair LVD

cables are required.

c. Connect the DC power cable to the drive. See Figure 3.

Figure 3. Cable connections and external termination

7. Format the drive

The drive has been low level formatted at the factory. You do not need to

perform another low level format on this drive unless you decide to perform

certain diagnostics through the host adapter. If you do decide to perform a

low level format, do not abort during the format as this is likely to make the

drive inoperable. A low level format, with verification, will typically take two

hours.

Protect against power failure or other power interruptions during the format.

a. Turn on DC power to the host system.

b. Boot the system from a system floppy, CD, or from a previously

installed hard disc drive if there is one.

c. Format the drive.

Caution. Formatting a drive erases all user data. Be sure that you under-

stand this principle before formatting any hard disc drive. It is not

necessary to format a drive that previously has been used to

store data, unless your intention is to erase all user data. Seagate

is not responsible for lost user data.

Cheetah disc drives are designed to operate with a variety of operating sys-

tems. Please refer to your system or SCSI controller manual for information

about formatting and setting up the drive. Some quick desktop system

notes are provided below.

• Microsoft

. Set the drive type in CMOS to “Zero,” “None,” or “No hard

drive installed.” Use FDISK.EXE and FORMAT.EXE. Systems using Win-

dows 98 or later can create one single partition (drive letter) on the drive.

• Macintosh

. Use a third-party drive utility (most revisions of Apple’s HD

Setup utility only work with drives having special Apple firmware).

Troubleshooting

• Drive does not spin up. Check cables and all jumper settings. Make

sure cable pin 1 (edge stripe) matches PCB pin 1.

• Drive spins, but no LED on/off activity. Check SCSI ID setting. Set the

ID so that each device on the SCSI chain has its own unique ID. The host

I/O controller is usually ID7.

• Computer does not seem to recognize the drive. Verify that the drive

is enabled by the SCSI host adapter setup utility.

• FDISK does not detect the drive. Run the FDISK program located on

your Windows startup diskette. Type fdisk/status to verify that your hard

drive is present.

Seagate support services

For online information about Seagate products, visit www.seagate.com or e-

mail your disc questions to DiscSupport@Seagate.com.

If you need help installing your drive, consult your dealer first. If you need

additional help, call a Seagate technical support specialist. Before calling,

note your system configuration and drive model number (for example,

ST336706LW).

Africa +31-20-316-7222 Norway 800-113 91

Australia 1800-14-7201 Poland 00 800-311 12 38

Austria 0 800-20 12 90 Spain 900-98 31 24

Belgium 0 800-74 876 Sweden 0 207 90 073

Denmark 80 88 12 66 Switzerland 0 800-83 84 11

France 0 800-90 90 52 Singapore 800-1101-150

Germany 0 800-182 6831 Taiwan +886-2-2514-2237

Hong Kong 800-90-0474 Thailand 001-800-11-0032165

Indonesia 001-803-1-003-2165 Turkey 00 800-31 92 91 40

Ireland 1 800-55 21 22 United Kingdom 0 800-783 5177

Italy 800-790695 USA/Canada/ 1-800 SEAGATE or

Malaysia 1-800-80-2335 Latin America +1-405-936-1234

Middle East +31-20-316-7222 Other European

Netherlands 0 800-732-4283 countries +31-20-316-7222

New Zealand 0800-443988

Warranty. Contact your place of purchase or our web site (above).

Return Merchandise Authorization (RMA). Before returning the drive, verify that it

is defective. Seagate Worldwide customer service centers are the only facilities autho-

rized to service Seagate drives. Contact nearest center for return procedures and

trade regulations.

Shipping the drive

Caution. Back up the data before shipping. Seagate assumes no responsibility for

data lost during shipping or service. Shipping drive in an unapproved container voids

the warranty. Pack the drive with original box and packing materials. Use no other

materials. This prevents electrical and physical damage in transit.

Publication number: 100141983, Rev. A, May 2001, Printed in U.S.A.

Seagate, Seagate Technology, and the Seagate logo are registered trademarks of

Seagate Technology LLC. Barracuda is a registered trademark of Seagate Technology

LLC. Other product names are registered trademarks or trademarks of their owners.

Seagate reserves the right to change, without notice, product offerings or specifica-

tions.

Do not remove.

Do not install jumpers

on these four positions.

(default)

Note.

1 2

Comentarios a estos manuales

Sin comentarios

Seagate ST318406LW Guía de instalación Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para No Seagate ST318406LW