Seagate MEDALIST 275XE Guía de instalación

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .Medalist XE Family. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .

Standard installation1. Turn the computer on.2. Enter the System Setup routine. (Refer to your computeruser’s guide. System Setup may be calle

1,057 – 1,024 = 33, or 17.3 Mbytes. To avoid thisproblem, configure your System Setup manually.If none of the standard drive types offered in System S

PartitioningYou must partition the drive into one or more logical drives beforeyou can use it.Caution. Partitioning or formatting a drive at any leve

drive: designates the drive you are formatting. Type c: if youare formatting the boot drive or if your system contains onlyone drive. Type d: to forma

4. Select drive type 2 for your new ST3660A. If your computerdoes not offer drive type 2, use the following values: 615cylinders, 4 heads and 17

EZ-Drive is easy and safe to use and versatile. If you already havea drive installed, EZ-Drive will not alter its format and files unlessyou instruct

2. Type ez.3. Disregard the Notice dialog box. The EZ-Drive software isauthorized for installation only with the drive on which it isshipped. Press

Booting with a diskette after EZ-Drive is installedTo boot your computer with a diskette: 1. Boot the computer with the diskette-drive door open. 2. P

The computer will reboot when the partitioning process is com-plete. However, you must make sure the EZ-Drive installed driveis present to continue

You can re-establish the 32-bit disk access capability using theSETUP program on the EZ-Drive diskette as follows:1. Load Windows.2. Open the Program

© 1994 Seagate Technology, Inc. All rights reservedPublication Number: 36294-001, Rev. ADecember 1994Seagate, Seagate Technology and the Seagate

Basic troubleshootingWarning. Always turn off the computer before changing jumpersor unplugging cables and cards.Caution. Your drive and computer cont

if you have a large capacity drive, the translation geometrysettings must not exceed the limitations set by the operatingsystem and BIOS. Refer to the

• Check for I/O address conflicts. To isolate the conflict, firstverify that the drive and host adapter are compatible with yourcomputer by removing a

• Check all cables. Make sure the video card-cables are se-curely attached.• While the computer is powered down, remove the drive hostadapter. If th

During the DOS high-level format, the drive does not formatto full capacity.• Verify your computer’s System Setup drive-type values. Oneof the followi

The error message “Microsoft Windows 32-bit disk driver(WDCTRL) phase 03, 3f” appears when you open Windows.• A device conflict occurs between Micros

Disabling Maximum OverdriveYou can disable Maximum Overdrive during the installation proc-ess or anytime afterward. To disable it during the instal

Technical support servicesIf you need assistance installing your drive, consult your dealer.Your dealer is knowledgeable of computer system configurat

Location Modem numberThailand 662-531-8111Australia 61-2-756-2359Korea 82-2-556-7294SeaFAXYou can use a touch-tone telephone to access Seagate’sau

Seagate CompuServe forumOnline technical support for Seagate products is available onCompuServe. To access the Seagate technical support fo-rum, type

Read before you begin...Application. Your Seagate® drive is designed for NRTL-listedpersonal computers. It uses the ATA interface.Warning. Turn off th

Storing and shipping your driveKeep your original box and packing materials for storing orshipping your drive. The box has a Seagate Approved

Seagate Technology, Inc.920 Disc Drive, Scotts Valley, CA 95066, USAPublication Number: 36294-001, Rev. A, Printed in USA

Maintenance and repair. Seagate drives do not require mainte-nance. The head/disc assembly is factory-sealed; a broken sealvoids the warranty. Seagate

Front4-pinpower connector8-pinmaster/slave jumper blockFrontCable select40-pinATA interfaceconnector4321Circuit board+5V+5V return+12V return+1

Installing the drive1. Turn the computer off.Warning. Installing or removing the drive or adapter cardswhile the computer is powered on can damag

Attaching cablesRefer to Figure 1 on page 3 for the locations of the connectors.1. Connect the remote LED (optional). 2. Attach the power cable. Attac

Installing drives in computers that use cable-select:If your computer uses the cable-select method, refer to yourcomputer reference guide to determine

Configuring the computerYour computer maintains records representing the hardware inthe system. This representation includes the translation geometryt