Seagate ST5660A Manual de usuario

Intel 430TX PCI ChipsetIntelligentMAIN BOARDATX586forDual CPUs ATX FactorTX2forAT Factor / Wide SCSIUSER’S MANUALversion 1.0

10Map of ATX586 Mother Board Default Setting for Intel Pentium 133Mhz,AMD K5-133,CYRIX P166+ ,512K PB Cache1.2 Two-Jumper Setting for CPU

11JP6/JP7: Set CPU External Bus Frequency Rate (BF1, BF0)JP6/JP7: 1-2, SHORT forIntel 90/100Mhz, MMX233Mhz, AMD K5 75-133,AMD K6 PR233MhzJP6: 1-2 and

12JP8/9: Set CPU External Bus Frequency Selection (FS0, FS1, FS2)JP8: 1-2 and JP9: 2-3SHORT : 75Mhz for CX200+JP8/9:1-2 SHORT: 66Mhz for CX 166+, AMDK

13JP15: 2MB FLASH BIOS ONLY2-3 SHORT for normal (set by factory).Default.1-2 SHORT reserved for factory set only.JP16: Select FLASH BIOS2-3 SHORT for

14JP12: Choose CPU SMI Mode1-2 SHORT: SMI by PIIX4 ( Single CPU request SMI),Default.2-3 SHORT: SMI by IOAPIC (Dual CPU request SMI)1.4 Install Sys

158MB * 32 DS X 64MB8MB * 32 DS 1MB * 32 SS 72MB8MB * 32 DS 2MB * 32 DS 80MB8MB * 32 DS 4MB * 32 SS 96MB8MB * 32 DS 8MB * 32 DS 128MB16MB * 32SS X 128

16JP17: IR, fast infrared port. PIN-1: IRRX, PIN-2:GND; PIN-3: IRTX; PIN-4: VCCCOM1-2/CN1-CN5: Support 16550 high speedserial ports/ UART.PS/2 Mouse

17IDE 1: Primary IDE port to support ATAPI Mode 5IDE devicesIDE 2: Secondary IDE port to support ATAPI Mode 5IDE devices.FDC/CN8: Support 2 FDD up to

18JP8 Set CPU External Bus Frequency (FS0, FS1, FS2)JP9 Set CPU External Bus Frequency (FS0, FS1, FS2)JP12 Choose CPU SMI ModeJP13 2-3 Normal CMOS, 3-

19

2UPDATE INFORAMTIONJULY 22, 971) When you install ATX power supply, please connect CASESTANDBY to front panel connector CN9/JP9 , pin 19-20Power On.

20Chapter 2AWARD, PnPGREEN BIOSSETUP2.1 BIOS SetupPowe on the computer and press <DEL> key immediatelyand the screen will display you CMOS S

21of hard disk drive installed in the system, floppydrive type, and the type of display monitor.ROM PCI/ISA BIOS (2A59GT4A)STANDARD CMOS SETUPAWARD S

3CONTENTPreface ... 1CHAPTER 1 Hardware Installation forATX5864 1.1 One Jumper to

4 2.6 PNP/PCIConfiguration...18 2.7 IntegratedPeripherals...18 2.8 AWARD BIOS PostCode..

5CHAPTER 4 Hardware Installation for TX2 49 4.1 One Jumper to Set CPU...… 50 4.2 Two Jumper to Set CPU...…………… 52 4.

6PrefaceInside the DocumentThis document describes setup ATX586 Dual Pentium Main Board withIntel 430TX PCI CHIPSET, resulting in Ultra IDE performanc

7(Chapter 4 is about positions, jumpers and connectors for TX2.Due to the board supports full range of Pentium CPU MMX 75Mhz-233Mhz, AMD K5/K6-PR233

8² 24 Programmable Interrupts: 13 ISA supported; 4 PCI; 1 interrupt/SMI# rerouting; 2 motherboard ; 1 interrupt used for INTR input; 3general purpose;

9Chapter 1Hardware Installation For ATX5861.1 One Jumper to Set CPU , Simple JumperNo more CPU jumper setting when you use Single ProcessorIntel 13